304 stainless steel pipe and tube (UNS S30400, EN 1.4301) is the general-purpose 18 % chromium, 8–11 % nickel austenitic grade; 304L (S30403) limits carbon to 0.035 % for welded construction. In ASTM A312 pipe, TP304 requires at least 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield strength, and TP304L at least 70 ksi [485 MPa] and 25 ksi [170 MPa]. This page collects the chemistry, strength, physical properties, equivalent designations and the ASTM pipe and tube standards that list 304, each from the standard named.
Chemical composition of 304, 304L and 304H pipe (ASTM A312)
Maximum values unless a range is shown, in weight percent, from ASTM A312/A312M-24b, Table 1.
| Grade | UNS | C max | Mn max | P max | S max | Si max | Cr | Ni |
|---|---|---|---|---|---|---|---|---|
| TP304 | S30400 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–11.0 |
| TP304L | S30403 | 0.035* | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–13.0 |
| TP304H | S30409 | 0.04–0.10 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–11.0 |
* Footnote D to Table 1: for small diameter or thin walls or both, where many drawing passes are required, a carbon maximum of 0.040 % is necessary in grades TP304L and TP316L.
Mechanical properties (ASTM A312 minimums)
From ASTM A312/A312M-24b, Table 4. A312 publishes these values in ksi with MPa in brackets; the MPa figures are the standard’s own rounded values. Use the ksi to MPa converter for other figures.
| Grade | Tensile strength, min | Yield strength, min |
|---|---|---|
| TP304 | 75 ksi [515 MPa] | 30 ksi [205 MPa] |
| TP304L | 70 ksi [485 MPa] | 25 ksi [170 MPa] |
| TP304H | 75 ksi [515 MPa] | 30 ksi [205 MPa] |
Equivalent designations
From EN 10088-1:2023, Table A.1, which rates these cross-references as comparable rather than identical grades. More grades are in the stainless steel grades chart.
| System | 304 | 304L |
|---|---|---|
| UNS (ASTM A959) | S30400 | S30403 |
| EN number / name | 1.4301 / X5CrNi18-10 | 1.4307 / X2CrNi18-9 (also 1.4306) |
| JIS | SUS304 | SUS304L |
| GB/T 20878 | S30408 | S30403 |
Physical properties
Guidance values from EN 10088-1:2023, Annex E (Table E.1) for steels 1.4301 and 1.4307; melting ranges from the SSINA Designer Handbook (Table 10) and the AK Steel 304/304L product data sheet. Details: stainless steel density, stainless steel melting point.
| Property (20 °C) | 304 / 304L (EN 1.4301 / 1.4307) |
|---|---|
| Density | 7.9 g/cm³ (7,900 kg/m³) |
| Modulus of elasticity | 200 GPa |
| Mean thermal expansion, 20–100 °C | 16.0 × 10⁻⁶ /K |
| Thermal conductivity | 15 W/(m·K) |
| Specific heat capacity | 500 J/(kg·K) |
| Electrical resistivity | 0.73 Ω·mm²/m |
| Magnetizable (annealed) | No |
| Melting range | 1,398–1,454 °C for 304 (SSINA); 1,399–1,454 °C for 304/304L (AK Steel) |
EN 10088-1 notes that martensite formed by cold deformation, or small amounts of ferrite, increase the magnetizability of austenitic grades, so cold-worked or welded 304 can show slight magnetic response.
304 vs 304L vs 304H
- 304: carbon up to 0.08 %; the standard choice where the pipe or tube is not welded extensively or is solution annealed after welding.
- 304L: carbon up to 0.035 % in A312 (0.040 % for small or thin tube per footnote D); lower carbon reduces chromium carbide precipitation in weld heat-affected zones. Its minimum strength in A312 is lower than 304’s.
- 304H: carbon controlled at 0.04–0.10 % for strength at elevated temperature, as used in boiler and superheater service.
304 contains no molybdenum, so in chloride-bearing water or atmospheres 316/316L is usually chosen instead; see 304 vs 316 vs 316L.
ASTM standards that list 304 pipe and tube
| Standard | Product | 304 grades listed |
|---|---|---|
| ASTM A312/A312M-24b | Seamless, welded and heavily cold-worked austenitic stainless steel pipe | TP304, TP304L, TP304H |
| ASTM A213/A213M-24 | Seamless boiler, superheater and heat-exchanger tubes | 304, 304L (S30400, S30403) |
| ASTM A249/A249M-24a | Welded boiler, superheater, heat-exchanger and condenser tubes | 304, 304L (S30400, S30403) |
| ASTM A269/A269M-25 | Seamless and welded austenitic stainless steel tubing for general service | 304, 304L (S30400, S30403) |
| ASTM A270/A270M-24 | Seamless and welded austenitic stainless steel sanitary tubing | 304, 304L (S30400, S30403) |
Sizes and weights: stainless steel pipe schedule chart (ASME B36.19), stainless steel tube size chart and the stainless steel weight calculator. Pressure ratings: stainless steel pipe and tube pressure rating chart.


