Tube gauge (BWG, Birmingham Wire Gage) is the number used to state the wall thickness of heat exchanger and instrument tubing: the higher the gauge number, the thinner the wall. 16 BWG is 0.065 in (1.65 mm), 14 BWG is 0.083 in (2.11 mm) and 18 BWG is 0.049 in (1.24 mm). The charts below give every gauge listed in TEMA Table D-7 and the inside diameter and weight for each tube OD.
BWG tube gauge chart: wall thickness in inches and mm
Wall thickness for each BWG gauge as listed in the TEMA Standards, 11th Edition (2023), Table D-7 “Characteristics of Tubing”. Millimetre values are converted from inches (× 25.4) and rounded.
| BWG gauge | Wall thickness, in | Wall thickness, mm |
|---|---|---|
| 7 | 0.180 | 4.57 |
| 8 | 0.165 | 4.19 |
| 10 | 0.134 | 3.40 |
| 11 | 0.120 | 3.05 |
| 12 | 0.109 | 2.77 |
| 13 | 0.095 | 2.41 |
| 14 | 0.083 | 2.11 |
| 15 | 0.072 | 1.83 |
| 16 | 0.065 | 1.65 |
| 17 | 0.058 | 1.47 |
| 18 | 0.049 | 1.24 |
| 19 | 0.042 | 1.07 |
| 20 | 0.035 | 0.89 |
| 22 | 0.028 | 0.71 |
| 24 | 0.022 | 0.56 |
| 26 | 0.018 | 0.46 |
| 27 | 0.016 | 0.41 |
Tube OD and gauge chart: inside diameter and weight
Every OD and gauge combination in TEMA Table D-7, from 1/4 in to 3 in OD. Inside diameter is from the table. Weights are calculated with the method of the table footnote: TEMA bases weight on low carbon steel at 0.2836 lb/in³ and gives a factor of 1.02 for 300-series stainless steels, so the weight here is the carbon steel weight × 1.02.
| Tube OD, in (mm) | BWG | Wall, in (mm) | Inside diameter, in (mm) | Weight, 300-series stainless, lb/ft | Weight, 300-series stainless, kg/m |
|---|---|---|---|---|---|
| 1/4 (6.35) | 22 | 0.028 (0.71) | 0.194 (4.93) | 0.068 | 0.101 |
| 24 | 0.022 (0.56) | 0.206 (5.23) | 0.055 | 0.081 | |
| 26 | 0.018 (0.46) | 0.214 (5.44) | 0.046 | 0.068 | |
| 27 | 0.016 (0.41) | 0.218 (5.54) | 0.041 | 0.061 | |
| 3/8 (9.52) | 18 | 0.049 (1.24) | 0.277 (7.04) | 0.174 | 0.259 |
| 20 | 0.035 (0.89) | 0.305 (7.75) | 0.130 | 0.193 | |
| 22 | 0.028 (0.71) | 0.319 (8.10) | 0.106 | 0.158 | |
| 24 | 0.022 (0.56) | 0.331 (8.41) | 0.085 | 0.126 | |
| 1/2 (12.70) | 16 | 0.065 (1.65) | 0.370 (9.40) | 0.308 | 0.459 |
| 18 | 0.049 (1.24) | 0.402 (10.21) | 0.241 | 0.359 | |
| 20 | 0.035 (0.89) | 0.430 (10.92) | 0.177 | 0.264 | |
| 22 | 0.028 (0.71) | 0.444 (11.28) | 0.144 | 0.214 | |
| 5/8 (15.88) | 12 | 0.109 (2.77) | 0.407 (10.34) | 0.613 | 0.913 |
| 13 | 0.095 (2.41) | 0.435 (11.05) | 0.549 | 0.817 | |
| 14 | 0.083 (2.11) | 0.459 (11.66) | 0.491 | 0.730 | |
| 15 | 0.072 (1.83) | 0.481 (12.22) | 0.434 | 0.646 | |
| 16 | 0.065 (1.65) | 0.495 (12.57) | 0.397 | 0.591 | |
| 17 | 0.058 (1.47) | 0.509 (12.93) | 0.359 | 0.534 | |
| 18 | 0.049 (1.24) | 0.527 (13.39) | 0.308 | 0.458 | |
| 19 | 0.042 (1.07) | 0.541 (13.74) | 0.267 | 0.397 | |
| 20 | 0.035 (0.89) | 0.555 (14.10) | 0.225 | 0.335 | |
| 3/4 (19.05) | 10 | 0.134 (3.40) | 0.482 (12.24) | 0.900 | 1.340 |
| 11 | 0.120 (3.05) | 0.510 (12.95) | 0.824 | 1.227 | |
| 12 | 0.109 (2.77) | 0.532 (13.51) | 0.762 | 1.134 | |
| 13 | 0.095 (2.41) | 0.560 (14.22) | 0.679 | 1.010 | |
| 14 | 0.083 (2.11) | 0.584 (14.83) | 0.604 | 0.898 | |
| 15 | 0.072 (1.83) | 0.606 (15.39) | 0.532 | 0.792 | |
| 16 | 0.065 (1.65) | 0.620 (15.75) | 0.486 | 0.723 | |
| 17 | 0.058 (1.47) | 0.634 (16.10) | 0.438 | 0.651 | |
| 18 | 0.049 (1.24) | 0.652 (16.56) | 0.375 | 0.557 | |
| 20 | 0.035 (0.89) | 0.680 (17.27) | 0.273 | 0.406 | |
| 7/8 (22.22) | 10 | 0.134 (3.40) | 0.607 (15.42) | 1.083 | 1.611 |
| 11 | 0.120 (3.05) | 0.635 (16.13) | 0.988 | 1.470 | |
| 12 | 0.109 (2.77) | 0.657 (16.69) | 0.911 | 1.355 | |
| 13 | 0.095 (2.41) | 0.685 (17.40) | 0.808 | 1.203 | |
| 14 | 0.083 (2.11) | 0.709 (18.01) | 0.717 | 1.067 | |
| 15 | 0.072 (1.83) | 0.731 (18.57) | 0.631 | 0.938 | |
| 16 | 0.065 (1.65) | 0.745 (18.92) | 0.574 | 0.854 | |
| 17 | 0.058 (1.47) | 0.759 (19.28) | 0.517 | 0.769 | |
| 18 | 0.049 (1.24) | 0.777 (19.74) | 0.441 | 0.657 | |
| 20 | 0.035 (0.89) | 0.805 (20.45) | 0.321 | 0.477 | |
| 1 (25.40) | 8 | 0.165 (4.19) | 0.670 (17.02) | 1.502 | 2.236 |
| 10 | 0.134 (3.40) | 0.732 (18.59) | 1.265 | 1.883 | |
| 11 | 0.120 (3.05) | 0.760 (19.30) | 1.152 | 1.714 | |
| 12 | 0.109 (2.77) | 0.782 (19.86) | 1.059 | 1.576 | |
| 13 | 0.095 (2.41) | 0.810 (20.57) | 0.938 | 1.395 | |
| 14 | 0.083 (2.11) | 0.834 (21.18) | 0.830 | 1.235 | |
| 15 | 0.072 (1.83) | 0.856 (21.74) | 0.729 | 1.084 | |
| 16 | 0.065 (1.65) | 0.870 (22.10) | 0.663 | 0.986 | |
| 18 | 0.049 (1.24) | 0.902 (22.91) | 0.508 | 0.756 | |
| 20 | 0.035 (0.89) | 0.930 (23.62) | 0.368 | 0.548 | |
| 1 1/4 (31.75) | 7 | 0.180 (4.57) | 0.890 (22.61) | 2.100 | 3.126 |
| 8 | 0.165 (4.19) | 0.920 (23.37) | 1.952 | 2.905 | |
| 10 | 0.134 (3.40) | 0.982 (24.94) | 1.631 | 2.427 | |
| 11 | 0.120 (3.05) | 1.010 (25.65) | 1.479 | 2.201 | |
| 12 | 0.109 (2.77) | 1.032 (26.21) | 1.356 | 2.018 | |
| 13 | 0.095 (2.41) | 1.060 (26.92) | 1.197 | 1.781 | |
| 14 | 0.083 (2.11) | 1.084 (27.53) | 1.056 | 1.572 | |
| 16 | 0.065 (1.65) | 1.120 (28.45) | 0.840 | 1.250 | |
| 18 | 0.049 (1.24) | 1.152 (29.26) | 0.642 | 0.955 | |
| 20 | 0.035 (0.89) | 1.180 (29.97) | 0.464 | 0.690 | |
| 1 1/2 (38.10) | 10 | 0.134 (3.40) | 1.232 (31.29) | 1.996 | 2.971 |
| 12 | 0.109 (2.77) | 1.282 (32.56) | 1.653 | 2.461 | |
| 14 | 0.083 (2.11) | 1.334 (33.88) | 1.283 | 1.909 | |
| 16 | 0.065 (1.65) | 1.370 (34.80) | 1.017 | 1.514 | |
| 2 (50.80) | 11 | 0.120 (3.05) | 1.760 (44.70) | 2.460 | 3.661 |
| 12 | 0.109 (2.77) | 1.782 (45.26) | 2.248 | 3.345 | |
| 13 | 0.095 (2.41) | 1.810 (45.97) | 1.974 | 2.937 | |
| 14 | 0.083 (2.11) | 1.834 (46.58) | 1.735 | 2.582 | |
| 2 1/2 (63.50) | 10 | 0.134 (3.40) | 2.232 (56.69) | 3.457 | 5.145 |
| 12 | 0.109 (2.77) | 2.282 (57.96) | 2.842 | 4.230 | |
| 14 | 0.083 (2.11) | 2.334 (59.28) | 2.188 | 3.256 | |
| 3 (76.20) | 10 | 0.134 (3.40) | 2.732 (69.39) | 4.188 | 6.233 |
| 12 | 0.109 (2.77) | 2.782 (70.66) | 3.436 | 5.114 | |
| 14 | 0.083 (2.11) | 2.834 (71.98) | 2.640 | 3.929 |
The calculated carbon steel weights agree with the weights printed in Table D-7 within 1% for every row except 3/4 in OD × 10 BWG, where the table prints 0.833 lb/ft and the footnote method gives 0.883 lb/ft. For other ODs and walls, use the stainless steel weight calculator.
Weight factors for other tube materials
The footnote of TEMA Table D-7 converts the carbon steel weight to other tube metals with these factors:
| Material (TEMA footnote wording) | Multiply carbon steel weight by |
|---|---|
| A.I.S.I. 300 series stainless steels | 1.02 |
| A.I.S.I. 400 series stainless steels | 0.99 |
| Nickel | 1.13 |
| Nickel-copper | 1.12 |
| Nickel-chrome-iron | 1.07 |
| Copper and cupro-nickels | 1.14 |
| Admiralty | 1.09 |
| Aluminum brass | 1.06 |
| Aluminum bronze | 1.04 |
| Titanium | 0.58 |
| Aluminum | 0.35 |
Tube gauge is not sheet metal gauge
- Different systems. BWG is used for tube walls. Sheet and plate are often quoted in other gauge systems, and the same gauge number does not give the same thickness across systems, so a “16 gauge” sheet thickness should not be used for a 16 BWG tube.
- Needle tubing uses its own gauges. Medical needle sizes such as 18G or 21G follow ISO 9626, a different system; see the needle gauge chart.
- Pipe uses schedules, not gauges. Pipe walls are set by schedule (for example Schedule 10S or 40S); see the stainless steel pipe schedule chart.
How to specify heat exchanger tubing by gauge
- OD × gauge and decimal wall: for example 3/4 in OD × 16 BWG (0.065 in / 1.65 mm). Common tube ODs in TEMA Table D-7 run from 1/4 in to 3 in.
- Minimum or average wall: ASTM A1016-23 (clause 5.1.5), the general requirements standard for ferritic, austenitic and duplex stainless steel tubes, lists the size on the order as outside diameter and average or minimum wall thickness. ASTM A213 covers tubes in minimum wall thickness or, if specified in the order, average wall thickness. The permitted wall variations then follow the product specification.
- Specification and grade: ASTM A213 for seamless boiler, superheater and heat exchanger tubes, ASTM A249 for welded heat exchanger tubes, ASTM A269 for general service tubing.
- Tube sheet: the tube OD and gauge also set the tube sheet hole size and the tube-to-tubesheet joint; see tube sheet for heat exchangers.
For metric tube sizes and weights, see the stainless steel tube size chart; more charts and converters are listed under technical resources.
Sources: TEMA, Standards of the Tubular Exchanger Manufacturers Association, 11th Edition (2023), Section 9, Table D-7 Characteristics of Tubing and its footnote (pages 9-41 and 9-42); ASTM A1016/A1016M-23, clause 5.1.5; ASTM A213/A213M-24, section 1 (scope).


