Does Stainless Steel Rust? Why It Happens and How to Prevent It

Does stainless steel rust: illustration of the four common causes of rust on stainless steel

Does Stainless Steel Rust? Why It Happens and How to Prevent It

Will Lee - Account Manager, European Market at TeCarve
Will Lee
November 17, 2026
12 Min Read

Yes, stainless steel can rust. It resists corrosion because the chromium in it forms a thin passive film on the surface, and that film re-forms on its own when scratched. Stainless steel rusts when something breaks down that film faster than it can repair itself or stops it forming in the first place: chlorides, iron contamination, welding damage or crevices. Choosing the right grade and keeping the surface clean prevent most cases.

Short answer: stainless steel is “stain-less”, not stain-proof. EN 10088-1:2023 defines stainless steels as steels with at least 10.5 % chromium and at most 1.20 % carbon. That chromium makes the surface self-protecting in normal air and water. In salty or chloride-rich service, or when the surface is contaminated with ordinary steel, even 304 can show rust; 316 / 316L or duplex 2205 resist those conditions better.

Why stainless steel does not normally rust

Ordinary carbon steel rusts because iron reacts with oxygen and water and the rust flakes away, exposing fresh steel. In stainless steel the chromium forms a very thin, adherent chromium-rich oxide film instead. ASTM A967 describes stainless steels as “autopassivating”: the passive film forms by itself in air as long as the surface is clean and free of scale and foreign matter. If the film is scratched, it re-forms. That is the whole difference between stainless and galvanized or painted steel, where protection comes from a coating (see stainless steel vs galvanized pipe).

Why stainless steel rusts: the four common causes

CauseWhat you seeWhat to do
Chlorides (salt, coastal air, de-icing salt, pool water, some process fluids)Small pits or rust spots that come back after cleaning, often under deposits or in crevicesRinse chlorides off regularly; use a molybdenum grade such as 316 / 316L, or duplex 2205 for harsher service
Free iron on the surface (steel tools, grinding dust, steel brushes, nearby carbon-steel work)Light orange rust spots or streaks on an otherwise sound surfaceRemove the contamination and passivate to ASTM A967 / A380; keep stainless separate from carbon-steel tooling
Welding (heat tint and, in higher-carbon grades, chromium carbides at grain boundaries)Discoloration along welds; corrosion concentrated in the heat-affected zoneRemove heat tint by pickling (passivation alone does not remove it); use low-carbon L grades for welded construction
Crevices and deposits (under gaskets, clamps, dirt, scale)Corrosion hidden under a deposit or at a jointDesign out crevices where possible and keep surfaces clean

1. Chlorides: pitting and crevice corrosion

Chloride ions attack the passive film locally. The result is pitting: small, deep spots of corrosion rather than general rusting. Crevices, where the liquid is stagnant and oxygen cannot reach the surface to repair the film, are attacked first. This is why stainless fittings near the sea, around swimming pools or on roads treated with de-icing salt are the most common places to find rust on stainless steel. Molybdenum improves resistance to pitting; it is the main difference between 304 and 316 (see 316 vs 316L).

2. Free iron contamination

Much of the “rust on stainless” seen on new equipment is not the stainless steel corroding at all, but particles of ordinary iron on its surface. ASTM A967 lists the typical sources: steel tooling, grinding and blasting media, steel hooks, chains or forks, nearby work on carbon steel, and residual pickling salts. These particles rust and also stop the passive film from forming evenly. Passivation to ASTM A967, with cleaning and pretreatment to ASTM A380, removes them; see the passivation guide.

3. Welding: heat tint and sensitization

Welding leaves an oxide heat tint that is less protective than the normal passive film; it has to be removed by pickling or descaling, because passivation alone does not remove heat tint or scale (ASTM A967). In higher-carbon austenitic grades, welding heat can also cause chromium carbides to form at the grain boundaries, leaving the metal next to them short of chromium and open to intergranular attack. ASTM A262 gives the standard practices for detecting this susceptibility. Low-carbon grades reduce the risk: ASTM A312 limits carbon to 0.035 % in TP304L and TP316L, against 0.08 % in TP304 and TP316.

4. Crevices and deposits

Under gaskets, clamps, deposits, dirt or scale, the surface is starved of oxygen and the passive film cannot repair itself. Corrosion can start there even when the exposed surface looks perfect. Good design (avoiding tight crevices and dead legs) and regular cleaning are the practical answers.

Pitting corrosion and PREN: which grades resist rust better

The pitting resistance equivalent (PRE) is a simple number used to compare grades. EN 10088-1:2023, Annex D, gives the most common formula for austenitic and duplex grades as PRE = Cr + 3.3 Mo + 16 N. The values below use the minimum composition of each grade.

GradeMinimum Cr, %Minimum Mo, %Minimum N, %PRE from minimum compositionSource of composition
304 / 304L18.0——18.0ASTM A312, Table 1
316 / 316L16.02.00—22.6ASTM A312, Table 1
2205 (S32205)22.03.00.1434.1ASTM A790, Table 2

EN 10088-1 notes that PRE should not be used as an absolute value, because pitting resistance depends on the material and the environment together; it is a way to compare stainless steels. A minimum PRE can be agreed at the time of enquiry and order. More grades: stainless steel grades chart; for duplex see 2205 and 2507.

Does stainless steel rust in water, salt water or outdoors?

  • Fresh water and indoor air: clean 304 and 316 normally stay rust-free, because the passive film keeps repairing itself.
  • Salt water and coastal air: chlorides make pitting and crevice corrosion likely in 304; 316 / 316L is the usual minimum, and duplex or higher-alloy grades are used where the exposure is severe.
  • Outdoors near roads: de-icing salt behaves like sea spray; surfaces that are not washed by rain need more frequent cleaning.
  • Kitchens and food plants: rust spots usually come from steel wool, steel brushes or chloride cleaners rather than from the stainless steel itself.

How to remove rust from stainless steel and stop it coming back

  1. Clean off deposits and chlorides with water and a non-chloride cleaner.
  2. Remove light rust and iron particles with a non-metallic pad; never use steel wool or carbon-steel brushes, which leave new iron behind.
  3. For fabricated equipment, specify passivation to ASTM A967 after cleaning to ASTM A380, and pickling where there is weld heat tint.
  4. If rust keeps returning in the same place, look for a crevice, a chloride source or a grade that is too low for the environment.

For pipe and tube buyers: what to specify

  • Grade for the environment: 304 / 304L for general service, 316 / 316L where chlorides are present, duplex 2205 for higher chloride or strength demands.
  • Low-carbon grades for welded systems: TP304L / TP316L to ASTM A312 (carbon 0.035 % max).
  • Surface condition: pickled, bright annealed or polished, and passivation to ASTM A967 where required.
  • Intergranular corrosion testing: ASTM A262 can be specified where welded service or the process calls for it.

Related: carbon steel vs stainless steel, 304 stainless steel pipe and tube, is stainless steel magnetic.

Sources: EN 10088-1:2023, clause 3.1 and Annex D; ASTM A312/A312M-24b, Table 1; ASTM A790/A790M-24, Table 2; ASTM A967/A967M-25 and A380/A380M-25; ASTM A262 (scope).

Written by Will Lee, Account Manager (Europe), TeCarve · Reviewed against ASTM / EN / ISO source documents · How we write and review our technical guides →
Will Lee - Account Manager, European Market at TeCarve

Author: Will Lee

Will Lee is TeCarve's Account Manager for Europe and the author of TeCarve's technical guides on stainless steel pipe and tube. His article on ASTM A312, A213 and A249 tubing was published in Stainless Steel World (October 2026). He reviews buyer specifications and drawings against ASTM, EN and DIN standards, advises on grade, tolerance and testing requirements, and checks the mill test certificates issued by the producing plants before European shipments.